This tutorial was written for PSP 7
It can be easily done in other versions of PSP.
If you have a problem, please let me know.

It uses selections. You may download the zip- file for the selections here.
The zip with the other supplies here.

Save the selections to your selections folder in PSP.
Save your supplies in a folder and open them as needed.

Wave swing

Step 1. Open a new image 600 by 600

Step 2. Make a new layer and call it "step". Load the step selection from disk.
Flood fill with white. Go to Texture Effects and use the "stucco" preset.

Step 3. Make a new layer call it foundation. Load the foundation selection from disk.
Flood fill it with white and use the same stucco texture preset.

Step 4. Add a new layer call it middle. Load the "middle" selection from disk.
Flood fill with the fill blue. Go to inner bevel and use the "soft edge" preset.

Step 5. Make a new layer name it middle 2. Load the middle 2 selection from disk .
Flood fill it with the same blue and apply the same inner bevel.

Step 6. Make a new layer call it sides. Load the sidesselection from disk .
Flood fill with color #FF4040 . Apply the same inner bevel

Step 7. make a new layer call it windows. Load the windows selection from disk.
Flood fill it with white and go to selections > select all > float. Go to
effects > cutout and use these setting- vertical 3, horizontal 3, opacity 100. Blur 20

Step 8. Make a new layer call it door. Flood fill with white. Use same cutout.
Don't deselect. Open up ms-theaterdoor door and copy and paste into selection.

Step 9. Open up psp ms-theaterrope and paste as a new layer, name the layer "rope".
Positionection it to fit the left side. Then copy that rope layer and position it
on the right side.

Step 10. Add a new layer call it top. Load the top selection from disk.
Flood fill with color #FFFCO. Go to selection > select all > selection > float.
Apply a cutout using these settings.
vertical 3, horizontal 3, opacity 100. blur 20

Step 11 . Add a new layer call it top cap. Load from disk top cap. Flood fill FF4040.
Go to inner bevel. Us the same setting as before.

Step 12. Add a new layer call it ring. Load from disk ring. Flood fill with
metallic gradient. Go to inner bevel use round change the width to 8.

Step 13. Make a new layer call it inner ring. Load from disk inner ring.
Flood fill with # FF4040 red. Use same inner bevel as above.

Step 14. Add a new layer call it middle ring.Load from Disk middle ring.
Flood fill with FFFCO yellow. Go to select all float. Go to cut out use the
same cut out as in step 7.

Step 15. Add a new layer call it decor. Load from disk decor. Go to
selection expand by 3 flood fill with #FFFCO red. Go to inter bevel use
soft edge same as before.

Step 16. Add a new layer reload deco again flood fill with same red. Go to
inner bevel use frame, but change the width to 6

Step 17. Add a new layer call it circle deco. Load from disk circle deco.
Flood fill with # COCOFF blue. Go to float go to cutout use the same cut out.

Step 18. Add a new layer call it pole. Load from disk pole flood file with
same metallic gradient. go to inner bevel use round but change the width to 5

Step 19. Add a new layer call it middle 3. Load from disk middle 3. Flood
fill with fill blue color. Go to inner bevel use the soft edge again make
sure you change the width to 4.

step 20. Add a new layer call it swing bar. Load from disk swing bar. flood
fill with FFFC0 yellow. Go to inner bevel round use these. width 5 smooth 3
depth 3 ambiance 0 shiniest o angle 315 int. 45 elev 35

Step 21. Add a new layer call it swings line. Load from disk swing line.
flood fill with metallic gradient. Go to effect texture-sculpture. Use these
setting. silver Width 100, smoothness 3 depth 4 ambiance 0 shininess 0 angle
307 intensity 40 elevation 33

Step 22. Add a new layer call it seats. Load the seats selection from disk.
Flood fill with white. Deselect. Use magic wand on each seat and go to select
modify-expand 1. Then flood fill with color of your choice.
I used yellow, red, and blue. After you have them all filled, go to cutout
and use the same setting as before.

Done at last.

Tube and enjoy!

I hope that you were able to follow this tutorial.
If you have any questions, please e- mail me

Home     Back

This tutorial was maded nyt Opal, 2002.
This tutorial may not be sent by e- mail. You may link to it by a TEXT link only.
You may copy for personal instruction but it may not be published in print or on the web without prior written permission from Opal.