Put everything on it's own layer
1. Load from disk "middle section" and flood fill with brick
pattern at 100%.
Go to "Effects" "inner bevel" and use the "soft edge"
preset.
2. Load from disk "roof". Flood fill with the roof pattern
at 100%.
Go to "Effects" "cutout" and use these settings- ver 3, hor 3,
opacity 60, blur 20.
2 b. Load from disk "roof trim" and fill with color
#705B45.
Go to "Texture Effect" "texture" and use the paper
preset.
Next go to "Effects" "Inner bevel" and use the round preset,
but change the width to 4.
3. Load from disk "foundation". Flood fill with
#CDBFB2.
Go to "Texture effect" "texture" and use the stucco preset,
but change the size to 30.
Go to "Effects" "Drop shadow" and use these
settings- ver & hor 5, opa.100, blur 30, color black.
4. Load from disk "sides". Flood fill with brick at
80%.
Go to "Effects" "Inner bevel" and use the round preset but change
the width to 4.
5. Load from disk "front porch". Flood fill with
#CDBFB2.
Go to "Effects" "inner bevel" and use the soft edge
preset.
Go to "Effects" "Noise" add 10%.
6. Load from disk "Front". Flood fill with brick fill at
100%.
Apply the "soft edge" inner bevel, but change size to 4.
Go to
drop shadow and use these settings. ver and hor 4, op 60, blur
27.1
7. Load from disk "small window center". Flood fill with
pattern glass at 100%.
8. Load from disk "inside window frame". Flood fill with
color #644F39.
Go to "Effects" "inner bevel" round preset, but change
the width to 9.
9. Load from disk "small frames windows". Flood fill with
color #644F39.
Go to "Effects" "inner bevel" and use the round
preset.
10. Load from disk "window bottom section". Flood fill with
color #644F39.
Go to "Effects" "inner bevel" and use the soft edge
preset.
Go to "texture effects" "blinds" and use these
settings-
width 4, opacity 72, color black, light from left top
checked.
11. Open psp door and copy and paste as a new layer and line
it up.
12. Load from disk "poles". Flood fill with #644F39. Go to
texture effect- blinds
and use these setting. width 4, opacity 72,
color black, light from let top checked.
13. Load from disk "front middle roof". Flood fill with
#644F39. Go to "Effects"
"inner bevel" and use the soft edge
preset.
Or you can go use the extra plugin and use the canvas
texture.
14. Load from disk "frame front roof". Flood fill with
#644F39.
Go to "Effects" "inner bevel" use the round preset but change
the width to 4.
Go to Texture effect, blinds use these
setting.
width 4, opacity 72, color black, light from left top
checked.
15. Load from disk "large window center". Flood fill with
glass fill at 100%.
16. Load from disk "large window middle" flood fill with
same color.
Go to "Effects" "inner bevel" and apply the round
preset.
17. Load from disk "large window frames". Flood fill with
same color.
Go to "Effects" "Inner bevel" and apply the round preset
but change the width to 8.
17b. Load from disk "large window bottom" flood fill with
#705B45.
Go to "inner bevel" and apply the soft edge preset.
Go to
"Effects" blinds and use these settings-
width 4 opacity 72 color black
light from left top check.
18. Load from disk "top center". Flood fill with glass fill
at 100%.
19. Load from disk "round window". Flood fill with glass
fill at 80%.
20. Load from disk "top 1" flood fill with brick fill at
50%.
go to "Selection float" then "Effects" "Cutout" and use these
settings.
ver 3, hor 3, opacity 60 blur 20.
21 Load from disk "window trim sides". Flood fill with
color.
Go to "Effects" "Innner bevel" use the soft edge preset.
Go
to "Effects" "blinds" use these setting.
width 4, opacity 72, color
black, light from left top checked.
22. Load from disk "step 1" flood fill with #E1D7CC.
Go
to "Effects" drop shadow use these setting ver & hor 5, opa.100, blur
30, color black.
23. Load from disk "step 2" finish the same as step
1
24. Load from disk "step 3" finish the same as step1
and
then line the step up the way you want them.
25. Load from disk "round frame". Flood fill with color
#644F39.
go to "Effects" "inner bevel" and use the round
preset.
26. Open up the psp cross and copy and paste it as a new
layer.
I used three. Check the sample for placement.
You can use
your own cross need to resize
and make 2 small one and one large
one
27.Go to layer merge all visible.
28. Go to image resize .Resize 80% make sure both boxes are
checked.
Don't forget to go to "Effects" "Sharpen" and sharpen
once
before you save it as a tub
.....and we are done :o)
I hope that you were able to follow this tutorial.
If you have any questions, please e- mail me
home back
This tutorial was
maded by Opal, 2002.
This tutorial may not be sent by e- mail.
You may link to
it by a TEXT link only.
You may copy for personal instruction but it may
not be published
in print or on the web without prior written
permission from Opal.
